共找到 150 條與 高溫合金鋼板及帶材 相關的標準，共 10 頁
JIS G 4902:2019 specifies requirements for corrosion-resistant and heat-resistant superalloy, nickel and nickel alloy plates and sheets (hereafter
Corrosion-resistant and heat-resistant superalloy, nickel and nickel alloy -- Plate, sheet and strip
This specification covers rolled precipitation hardenable nickel alloy (N07718) plate, sheet, and strip in the annealed condition (temper).The values
Specification for Precipitation-Hardening Nickel Alloy (UNS N07718) Plate, Sheet, and Strip for High-Temperature Service
1.1 This specification covers rolled precipitation hardenable nickel alloy (N07718)* plate, sheet, and strip in the annealed condition (temper
Standard Specification for Precipitation-Hardening Nickel Alloy (UNS N07718) Plate, Sheet, and Strip for High-Temperature Service
CNCL NO S/S
Metal Stock List, Carbon & Alloy Steel Sheet & Strip
1.1 This specification2 covers alloys in the form of rolled plate, sheet, and strip that are typically used for (though not limited) heat-resisting
Standard Specification for Heat and Corrosion Resistant High Temperature Alloy Plate, Sheet, and Strip
本標準規定了變形高溫合金的板（帶）材產品交貨的技術要求、試驗方法、檢驗規則、標志、包裝及質量證明書、訂貨內容等。 本標準適用于厚度為4mm-14mm的熱軋板材、厚度小于4mm的冷軋薄板和帶材。其他類型或規格的板(帶)材可參照使用。 當合同協議或?qū)Ｓ眉夹g文件中的規定與本標準中的規定不一致時，應以
General specification of superalloy plates and strips
本文件規定了鈦微合金化高強鋼熱連軋鋼板及鋼帶的牌號表示方法、訂貨內容、尺寸、外形、重量、技術要求、試驗方法、檢驗規則、包裝、標志和質量證明書。 本文件適用于一般結構、工程機械用鈦微合金化高強鋼熱連軋鋼板及鋼帶（以下簡稱“鋼板及鋼帶
Titanium microalloyed high strength steel hot rolled steel plate and strip
Nickel alloy steel sheets and strips for low temperature applications. Types and qualities
1.1 This specification covers rolled precipitation hardenable nickel alloy
Standard Specification for Precipitation-Hardening Nickel Alloy (UNS N07718) Plate, Sheet, and Strip for High-Temperature Service
本標準適用于厚度為4～14mm，使用溫度為600～950℃的鎳基和鐵基高溫合金熱軋板，可用于航空、航天、燃氣輪機及其它工業用的高溫承力部件
Hot-rolled heat-resisting superalloy plates
本規范涵蓋了識別碳鋼和低合金鋼、耐腐蝕和耐熱鋼及合金、馬氏體時效鋼和其他高合金鋼、鐵合金板材、帶材、板材以及飛機管材的程序
Identification Carbon and Low-Alloy Steels, Corrosion- and Heat-Resistant Steels and Alloys Sheet, Strip, Plate, and Aircraft Tubing
1. 范圍 本規范涵蓋熱軋厚板卷材，超出了規范A506和A507的尺寸限制。 產品分為三種指定類型：合金鋼、拉伸鋼和結構合金鋼。 合金鋼按化學成分要求供貨，主要用于通用或雜項用途，需滿足彎曲和中等成形要求。 拉伸鋼主要應用于嚴重冷塑性變形的應用，如深沖或嚴重成形部件。 結構鋼按化學成分和機械性能要求
Steel plates and strips, thick plates and coils, hot-rolled alloy drawing steel and structural steel
This specification covers procedures for identifying carbon and low-alloy steels, corrosion- and heat-resistant steels and alloys, maraging and other
Identification Carbon and Low-Alloy Steels, Corrosion- and Heat-Resistant Steels and Alloys Sheet, Strip, Plate, and Aircraft Tubing
Nickel and nickel alloy plate, sheet and strip
Nickel and nickel alloy plate, sheet and strip
